a 材料高阻測試測量如防靜電產品（防靜電鞋、防靜電塑料橡膠制品、計 算機房防靜電活動地板等）電阻值的檢測；

b 材料體積電阻(率)和表面電阻(率)測量；

c 電化學和材料測試,以及物理,光學和材料研究;

d 微弱電流測量如光電效應和器件暗電流測量。

體積表面電阻率測試儀使用方法 ：

1、接好電源線

確保電源為220VAC/50Hz

2、接通電源

將電流電阻量程置于 104 檔,電壓量程置于10V，然后開機。

3、調零

在“Rx”兩端開路的情況下,調零使電流表的顯示為0000 .注意：在“Rx”兩端不開路，如接在電阻箱或被測量物體上時調零后測量會產生很大的誤差。一般一次調零后在測試過程中不需再調零。 完畢后關機。

4、連接線路

接好測試線，將測試線將主機與屏蔽箱連接好，測體積電阻時測試按鈕撥到Rv邊，測表面電阻時測試按鈕撥到Rs邊。然后開機。

5、選擇合適的測量電壓

電壓選擇開關在后面板，注意，在測試過程中不要隨意改動測量電壓，可能因電壓的過高或電流過大損壞被測試器件或測試儀器;

6、測試

測量時從低檔位逐漸拔往高檔，每撥一次稍停留1～2秒以使觀察顯示數字， 當被測電阻大于儀器測量量程時，電阻表顯示“1”，此時應繼續將儀器撥到量程更高的位置，當測量?jī)x器有顯示值時應停下，當前的數字乘以檔次即是被測電阻值。當有顯示數字時不要再往更高次檔撥，否測儀器會過量程，機內保護電路開始工作，儀器測量準確度會下降。

7、 測試完畢將電阻電流量程拔至“104 ”檔，電壓量程調至10V后關閉電源

每測量一次均應將量程開關撥回到104“調零”檔的量程位置以免開機或測量端短路時而損壞儀器。

8、 測量電流及1015Ω以上超高電阻的測量應用測量電流后用歐姆定律以電壓除以電流計算電阻的方法，詳見8.5節內容。

9 、體積電阻和表面電阻轉換

在測試過程中，使用屏蔽箱在進行體積電阻和表面電阻轉換時，必須把電源關閉后進行檔位轉換，否則會導致電壓沖擊到主機無法顯示或損壞。

Standards and scope of application:

Volume surface resistivity tester completely accord with the national standard GB14102006 solid electrical insulation insulation resistance, volume resistivity and surface resistance test method of material ASTM, D257 DC resistance or conductance of insulating materials test methods such as standard.

A volume surface resistivity tester with different measuring electrodes (clamps) that measures the volume resistivity and surface resistivity or conductivity of different materials (solids, powders, or liquids). Applicable to rubber, plastic, film, and powder, liquid, and solid and paste shape of various insulation materials, volume and surface resistance value measurement. Besides measuring resistance, the instrument can measure weak current directly.

Application range of volume surface resistivity tester:

A material high resistance test measurement, such as anti-static products (anti-static shoes, anti-static plastic rubber products, computer room, anti-static floor, etc.) resistance detection;

Volume resistivity (rate) and surface resistance (rate) measurement of B material;

C electrochemical and material testing, as well as physical, optical, and material studies;

D weak current measurement, such as photoelectric effect and device dark current measurement.

Technical index of volume surface resistivity tester:

1. resistance measurement range: 1 * 104 to 1 * 1018 ohms, divided into ten ranges.

The measuring range of 2. current is 2 * 10-4A to 1 * 10-16A

3. all digital LCD display.

4. accuracy: accuracy is better than the table below

Range effective display range 20~30 RH<80%

104 0.01~19.99 5%

1050.01 to 19.995%

1060.01 to 19.995%

1070.01 to 19.995%

1080.01 to 19.995%

1090.01 to 19.995%

10100.01 to 19.99 5%+2 words

10110.01 to 19.99 5%+2 words

10120.01 to 19.99 5%+5 words

10130.01 to 19.99 10%+5 words

10140.01 to 19.99 10%+5 words

1014 more than 0.01 to 19.99 10-15%+5 words

The error may increase when the effective display range is exceeded. The accuracy of the test current is the same as that of the resistor, and the accuracy of the test voltage is 10%

5. use environment: temperature -10 ~ 50 DEG C, relative humidity <90%.

6. test voltage: DC10V, 50V, 100V, 250V, 500V, 1000V. + 10%

7. power supply form: AC, 220V, 50HZ, power consumption of about 10W.

8. instrument size: 300mm * 280mm * 150 mm.

9. quality: about 3.0KG.

Method for using volume surface resistivity tester:

1. Connect the power cord

Make sure the power is 220VAC/50Hz

2. Switch on the power

Put the current resistance range in the 104 gear, the voltage range is placed at 10V, and then turn on.

3, zeroing

In the "Rx" open end under the condition of zero to display the current scale is 0 note: do not open the "Rx" ends, such as the resistance box or the object to be measured at zero on the measurement will produce great error. After a single zeroing, no zeroing is needed during the test. Shutdown after completion.

4. Connecting lines

Connect the test line, connect the host to the shield box, and measure the volume resistance. The test button is set on the Rv side. When the surface resistance is measured, the test button is set to the Rs edge. Then boot.

5, select the appropriate measuring voltage

Voltage selector switch in the rear panel, note that during the test, do not arbitrarily change the measurement voltage, may be due to excessive voltage or excessive current damage test device or test instrument;

6, test

When measuring from the low level to high level gradually pulling, each dial again slightly for 1 to 2 seconds to make the observation of figures, when the measured resistance is greater than the instrument measurement range, the resistance table shows "1", this time should be allocated to the instrument range to a higher position, when the measurement instrument display value should be stop, the digital grade is multiplied by the measured resistance value. When there is a digital display, do not dial the higher gear again, or the measuring instrument will pass the measuring range, the protection circuit inside the machine will start to work, and the accuracy of the instrument measurement will decrease.

7 、 after testing, draw the resistance current range to "104" file, and the voltage range is adjusted to 10V, then turn off the power supply

Once measured, the range switch should be moved back to the range of the 104 "zero" shift so as not to start or measure the short circuit and damage the instrument at the same time.

8. Measuring current and measuring over 1015 ohm resistance. After measuring current, use Ohm's law to calculate the resistance by dividing voltage by current. See section 8.5.

9 volume resistance and surface resistance conversion

In the test process, when using a shielded box for volume resistance and surface resistance conversion, the power must be switched off after the gear shift, otherwise it will cause voltage shock to the host, can not show or damage.